Perun V3 HYBRID MOSFET for Version 3 AEG Gearbox

Perun V3 HYBRID MOSFET for Version 3 AEG Gearbox
Perun V3 HYBRID MOSFET for Version 3 AEG Gearbox
Perun V3 HYBRID MOSFET for Version 3 AEG Gearbox
Description

Perun V3 Hybrid replaces mechanical contacts in your airsoft replica or gel blaster and provides lots of useful features. Optical and magnetic sensors allow to eliminate many moving parts that are prone to damage, thus increasing the reliability. Adaptive trigger control allows switching from a very short trigger travel to a long one even in the field, with almost any trigger, including stock ones.

Works without the need for any modification with most V3 gearboxes in Tokyo Marui standard. For details and exceptions please refer to the manual.

Features:

  • Adjustable trigger sensitivity
  • Independently programmable firing modes
  • Active brake with adjustable braking power
  • Precocking (with spring release feature)
  • Binary trigger
  • 2-stage trigger
  • Rate of fire reduction
  • DMR mode
  • Low battery voltage alarm
  • Programming supported with a multicolor LED diode
  • DSG mode
  • Diagnostic system
  • Electronic resettable fuse

Feature description

Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels, ranging from very short pull needed to fire a shot, to a very long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field.

Independently programmed firing modes - Program the firing modes any way you like, setting safe, semi, burst or auto on both selector positions.

Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem).

Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, piston will remain in rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked.

2-stage trigger – Light trigger pull results with a single shot or burst, while a deeper pull will cause a burst or fully automatic fire. Following modes are available: semi – burst, semi – auto and burst – auto.

Binary trigger - Allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released.

Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.

DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields.

Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.

DSG – a sector gear detection mode specially prepared to work with dual sector gears.

Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.

Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

 

Programming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolor LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example semi on semi and binary trigger on auto.

Perun V3 Hybrid works without problems with any battery from 7V do 17V. It can also be used with most extreme setups.

Delivery

UK Deliveries

DESTINATION DELIVERY TIMES COST
Royal Mail Tracked 48 2-3 Working Days including Saturdays £4.50
Royal Mail Tracked 24 1-2 Working Days including Saturdays £5.50
DHL Mainland UK 1 Working Day excluding Saturdays £9.99

All aimed delivery times apply to items in stock. Orders placed after 12:00 will be dispatched the following working day, next day delivery does not include Saturday's or Sunday's. Some services are only available to UK mainland addresses.

Royal Mail services cover the following: Highlands, Islands, Scilly Isles and Isle of Man

Royal Mail 24 & 48 services are non insured services with delivery confirmation only, no tracking.

 

European Deliveries

We can ship to any European destinations. Simply choose your country and the correct price will show up in the basket. If we don't have your country setup on our website, please contact us via email to get a tailored shipping quote - Contact Us

Due to Brexit ruling, all goods shipped to Europe are now excluding taxes. You will likely incur your local tax rate plus a possible courier handling fee. Failure to pay customs charges could result in storage/returns charges.

Delivery times range from 2-4 days, 4-9 for remote areas.

 

Rest of the World

We can ship anywhere in the world, rates depend on size and weight so please get in touch for a tailored shipping quote - Contact Us

All goods shipped to the rest of the world are excluding taxes. You will likely incur your local tax rate plus a possible courier handling fee. Failure to pay customs charges could result in storage/returns charges.

 

Returns

Our returns system is easy, you have the right to cancel an order up to 14 days, please check our full returns policy here.

Customer Reviews (0)

Be the first to Write a Review for this item!

Sale Price: £76.37
In stock | usually dispatched in 24 Hours
Quick Code: PERUNV3
  • Li-Po Lithium battery protection & up to 14.8v
  • Gearbox precocking
  • Active Brake
  • Programmable fire selector modes
  • No moving parts thanks to sensitive optical sensors
Description

Perun V3 Hybrid replaces mechanical contacts in your airsoft replica or gel blaster and provides lots of useful features. Optical and magnetic sensors allow to eliminate many moving parts that are prone to damage, thus increasing the reliability. Adaptive trigger control allows switching from a very short trigger travel to a long one even in the field, with almost any trigger, including stock ones.

Works without the need for any modification with most V3 gearboxes in Tokyo Marui standard. For details and exceptions please refer to the manual.

Features:

  • Adjustable trigger sensitivity
  • Independently programmable firing modes
  • Active brake with adjustable braking power
  • Precocking (with spring release feature)
  • Binary trigger
  • 2-stage trigger
  • Rate of fire reduction
  • DMR mode
  • Low battery voltage alarm
  • Programming supported with a multicolor LED diode
  • DSG mode
  • Diagnostic system
  • Electronic resettable fuse

Feature description

Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels, ranging from very short pull needed to fire a shot, to a very long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field.

Independently programmed firing modes - Program the firing modes any way you like, setting safe, semi, burst or auto on both selector positions.

Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem).

Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, piston will remain in rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked.

2-stage trigger – Light trigger pull results with a single shot or burst, while a deeper pull will cause a burst or fully automatic fire. Following modes are available: semi – burst, semi – auto and burst – auto.

Binary trigger - Allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released.

Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.

DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields.

Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.

DSG – a sector gear detection mode specially prepared to work with dual sector gears.

Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.

Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

 

Programming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolor LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example semi on semi and binary trigger on auto.

Perun V3 Hybrid works without problems with any battery from 7V do 17V. It can also be used with most extreme setups.

Delivery

UK Deliveries

DESTINATION DELIVERY TIMES COST
Royal Mail Tracked 48 2-3 Working Days including Saturdays £4.50
Royal Mail Tracked 24 1-2 Working Days including Saturdays £5.50
DHL Mainland UK 1 Working Day excluding Saturdays £9.99

All aimed delivery times apply to items in stock. Orders placed after 12:00 will be dispatched the following working day, next day delivery does not include Saturday's or Sunday's. Some services are only available to UK mainland addresses.

Royal Mail services cover the following: Highlands, Islands, Scilly Isles and Isle of Man

Royal Mail 24 & 48 services are non insured services with delivery confirmation only, no tracking.

 

European Deliveries

We can ship to any European destinations. Simply choose your country and the correct price will show up in the basket. If we don't have your country setup on our website, please contact us via email to get a tailored shipping quote - Contact Us

Due to Brexit ruling, all goods shipped to Europe are now excluding taxes. You will likely incur your local tax rate plus a possible courier handling fee. Failure to pay customs charges could result in storage/returns charges.

Delivery times range from 2-4 days, 4-9 for remote areas.

 

Rest of the World

We can ship anywhere in the world, rates depend on size and weight so please get in touch for a tailored shipping quote - Contact Us

All goods shipped to the rest of the world are excluding taxes. You will likely incur your local tax rate plus a possible courier handling fee. Failure to pay customs charges could result in storage/returns charges.

 

Returns

Our returns system is easy, you have the right to cancel an order up to 14 days, please check our full returns policy here.

Customer Reviews (0)

Be the first to Write a Review for this item!